Conversation
Have been seen failure on hardware `PTP transparent clock (IEEE 802.1AS)`
where it fails on hardware in CI:
Test File: /home/styx/.ghmoon/kernelkit/infix/git/test/case/ptp/transparent_clock/ieee802dot1as.py
Test Cmdl: ['--profile', 'ieee802-dot1as']
2026-08-20 13:25:58 # Starting (2026-08-20 13:25:58)
2026-08-20 13:25:58 # host: monza
2026-08-20 13:25:58 # mgmt1: sw1p3
2026-08-20 13:25:58 # mgmt2: sw1p2
2026-08-20 13:25:58 # mgmt3: sw1p1
2026-08-20 13:25:58 # gm: styx3
2026-08-20 13:25:58 # data: e3
2026-08-20 13:25:58 # mgmt: e28
2026-08-20 13:25:58 # tc: styx2
2026-08-20 13:25:58 # uplink: e4
2026-08-20 13:25:58 # dnlink: e3
2026-08-20 13:25:58 # mgmt: e28
2026-08-20 13:25:58 # receiver: styx1
2026-08-20 13:25:58 # data: e4
2026-08-20 13:25:58 # mgmt: e28
2026-08-20 13:25:58 #
2026-08-20 13:25:58 # Waiting for DUTs to become reachable...
2026-08-20 13:25:58 # Probing styx3 on port sw1p3 for IPv6LL mgmt address ...
2026-08-20 13:25:58 # Testing using RESTCONF
2026-08-20 13:25:59 # YANG models downloaded.
2026-08-20 13:26:02 # Waiting for DUTs to become reachable...
2026-08-20 13:26:02 # Probing styx2 on port sw1p2 for IPv6LL mgmt address ...
2026-08-20 13:26:02 # Testing using RESTCONF
2026-08-20 13:26:02 # YANG models downloaded.
2026-08-20 13:26:06 # Waiting for DUTs to become reachable...
2026-08-20 13:26:07 # Probing styx1 on port sw1p1 for IPv6LL mgmt address ...
2026-08-20 13:26:07 # Testing using RESTCONF
2026-08-20 13:26:07 # YANG models downloaded.
2026-08-20 13:26:10 ok 1 - Set up topology and attach to DUTs
2026-08-20 13:26:12 ok 2 - Configure grandmaster (OC, priority1=1, p2p)
2026-08-20 13:26:14 ok 3 - Configure transparent clock (p2p-tc, ieee802-dot1as)
2026-08-20 13:26:15 ok 4 - Configure time receiver (OC, priority1=128, client-only)
2026-08-20 13:26:18 ok 5 - Wait for grandmaster port to become time-transmitter
2026-08-20 13:26:22 ok 6 - Wait for time receiver to reach time-receiver state
2026-08-20 13:26:23 ok 7 - Verify time receiver steps-removed equals 1
2026-08-20 13:31:31 not ok 8 - Wait for time receiver offset to converge
2026-08-20 13:31:31 # Exiting (2026-08-20 13:31:31)
2026-08-20 13:31:31 # Traceback (most recent call last):
2026-08-20 13:31:31 # File "/home/styx/.ghmoon/kernelkit/infix/git/test/case/ptp/transparent_clock/ieee802dot1as.py", line 173, in
2026-08-20 13:31:31 # until(lambda: ptp.has_converged(receiver, threshold_ns), attempts=180)
2026-08-20 13:31:31 # File "/home/styx/.ghmoon/kernelkit/infix/git/test/infamy/util.py", line 55, in until
2026-08-20 13:31:31 # raise Exception("Expected condition did not materialize")
2026-08-20 13:31:31 # Exception: Expected condition did not materialize
2026-08-20 13:31:31 # 1..8
test error, no plan
Add more debug to be able to investigate it when it occur.
Signed-off-by: Mattias Walström <lazzer@gmail.com>
The collection scales with port count (three ethtool calls per interface, incl. SFP EEPROM reads) and log size, and 120s is not always enough on a 28-port switch at the end of a full test run. Signed-off-by: Mattias Walström <lazzer@gmail.com>
Add board support for the Microchip EV23X71A evaluation board, based on the LAN969x (Laguna) family: a Cortex-A53 with a TSN capable switch core, 24 GbE copper ports over QSGMII, four 10G SFP+ cages, and an RGMII management port. The sample here reports part 0x969b, a LAN9696RED, one of the variants for which the driver offers PTP and PSFP. Ports are renamed from the device tree path each netdev carries, e1 through e28 for the front ports and e29 for management. The switch driver leaves naming to the kernel, and there is no port@28, so the kernel names end up one off from Microchip's numbering. Attaching 29 PHYs also takes far longer than the ten seconds hw-wait allows, so that timeout is now read from /etc/default/hw-wait. Infix builds its own boot chain rather than using the one the board ships with: Microchip's Trusted Firmware for BL2 and BL31, and their U-Boot for BL33, which carries the LAN969x support but leaves out blkmap, SquashFS, and sysboot. It keeps no environment in flash, so a writable environment cannot be used to bypass secure boot. That needs the ENV_IS_NOWHERE patch, since the board only ever asks for the location matching the medium it booted from. Trusted Board Boot needs mbed TLS to parse the X.509 in the FIP's certificates, from the 2.28 series ATF 2.8 builds against, hence the new mbedtls-atf package. Buildroot's mbedtls tracks 3.x, where the sources ATF expects are gone. Two ATF build variables are not obvious: KEY_ALG=ecdsa, since the LAN969x crypto driver is built around the Silex ECDSA engine, and GENERATE_COT=1, without which the FIP carries no certificates for the ROM to check. Trusted Firmware is pinned to a commit rather than a tag because no tag carries the fix for ERR-LAN969X-001, where the boot ROM's ECDSA verifier mishandles P-256 values with a leading zero byte. The eMMC layout keeps the fip and fip.bak partition names, which is how BL1 finds the firmware and its fallback, followed by the usual Infix partitions. See the board README for the strapping table, the rescue paths, and how to install and update. Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The CPU temperature was missing from show system on LAN969x and SparX-5. The kernel names the hwmon device s5_temp, which normalize_sensor_name() reduced to temp, taking s5_ for a vendor prefix, and nothing downstream recognized that as a die temperature. Each consumer/frontend carried its own list of names, and they disagreed: the CLI matched cpu, soc, core, ap- and cp<N>-, the WebUI dashboard cpu, soc and core plus radio, phy and sfp prefixes. A new SoC meant patching every one. Give the SoC a component of its own, class iana-hardware:cpu, with the die sensors as its children. Consumers then ask for a celsius sensor whose parent is a CPU, the same question over NETCONF, RESTCONF, the WebUI, and the CLI, and hwmon and thermal zone names are recognized in a single place. Names are keys, not descriptions, so keep them unique rather than collapsing them: s5_temp becomes s5-temp, cp0_temp becomes cp0-temp. This also brings in x86, where coretemp and k10temp never matched. The CLI 'show hardware' command groups sensors under any component that has them, not just modules, so the new CPU sensors are listed. Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
A device with empty storage has no slot to boot, so it falls back to DHCP on its own. Pointing the boot file at a rootfs.itb is therefore enough to bring a factory fresh board all the way up to a running system, with no console interaction and no netboot.scr, since the ixprepdhcp handler downloads and validates the image itself. From there the system can install itself: build the image, give the netbooted system an address, and stream it onto the eMMC. Document that, including the partition table warning that follows, which the first boot resolves when it grows the last partition. Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Copilot stopped reviewing on behalf of
troglobit due to an error
August 24, 2026 09:38
Contributor
|
USB test fails, please investigate. I suspect your commit about statd |
mattiaswal
requested changes
Aug 25, 2026
| @@ -0,0 +1,24 @@ | |||
| ################################################################################ | |||
| # | |||
| # mbedtls-atf | |||
Contributor
There was a problem hiding this comment.
Clearly state why this extra package is needed here.
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
2 participants
Add this suggestion to a batch that can be applied as a single commit.This suggestion is invalid because no changes were made to the code.Suggestions cannot be applied while the pull request is closed.Suggestions cannot be applied while viewing a subset of changes.Only one suggestion per line can be applied in a batch.Add this suggestion to a batch that can be applied as a single commit.Applying suggestions on deleted lines is not supported.You must change the existing code in this line in order to create a valid suggestion.Outdated suggestions cannot be applied.This suggestion has been applied or marked resolved.Suggestions cannot be applied from pending reviews.Suggestions cannot be applied on multi-line comments.Suggestions cannot be applied while the pull request is queued to merge.Suggestion cannot be applied right now. Please check back later.
Description
statd: refactor temp sensors, consolidate SoC sensor handlingdoc/: updatenetboot.md, how to flash a remote deviceChecklist
Tick relevant boxes, this PR is-a or has-a: